General Purpose Wide Band Amplifier 50 Hz-100 MHz

Here is a general purpose wide band amplifier with a wide bandwidth of 50 Hz to 100 MHz. Typical frequencies are 5 and 10 MHz, but any frequency from 50 Hz to 100 MHz can be used.

Output levels of this wide band amplifier are +35 dB at 100 kHz, +30 dB at 10 MHz, +17 dB at 100 MHz noise smaller than 10 uV across 50 ohms with RF input -30 dBm MAX.

Wide band Amplifier Schematic

read more "General Purpose Wide Band Amplifier 50 Hz-100 MHz"

AADE Filter Design-Analysis FREE Download

This Filter Software will design most classical passive ladder Low-pass Filter, High- pass Filter, Band-pass Filter, and Band-Reject filters and analyze them in both the frequency and time domains. You can also enter a schematic and parts list from a book or magazine for analysis. Almost All Digital Electronic.

Download AADE Filter Design

DESIGN

• Butterworth, Chebyshev, Elliptic (Caur), Bessel, Legendre and Linear Phase: low-pass, high-pass, band-Pass, and band-reject filters.
• Coupled Resonator band-pass filters
• Crystal Ladder band-pass filters using identical crystals. Ideal for Amateur construction from surplus or microprocessor crystals.

Download AADE Filter Design

ANALYSIS frequency domain

• Power Effective Gain
• Power Insertion Gain
• Voltage Effective Gain
• Voltage Insertion Gain
• Current Effective Gain
• Current Insertion Gain
• Input Impedance
• Output Impedance
• Group Delay
• Phase
• Return Loss

ANALYSIS time domain

• Impulse Response
• Step Response
• Pulse Response
• Tone Pulse Response (for band-pass filters)

Download AADE Filter Design

UTILITIES

• You can enter a schematic and parts list from a book or magazine for analysis or modification.
• Insert a filter in front of an existing filter or Append a filter to the end of an existing filter: These allow design of wideband band-pass filters consisting of low-pass/high-pass combinations.

More detail for AADE Filter Design and Analysis - Latest Version AADE Filter Design

read more "AADE Filter Design-Analysis FREE Download"

80 meter vertical

As I look forward to cooler weather I've starting to think about 80 meters. With the winter months 80 becomes quieter and a better band for "DX". 80 is also to best band for my 1929 transmitters. I'd like to put up a better 80 meter antenna. Right now my endfed wire is only 10'-15' off the ground. If works OK for Minnesota but not much else beyond that. The radiation angle is too high. My backyard was too recently a corn field. Nothing back there is tall enough to support a higher dipole or end fed wire.

I'm going to start with a 30' to 35' 80 meter center loaded vertical and maybe even top load it a little. For a mast I'm going to try some of the fiberglass camouflage netting support poles / antenna masts seen on ebay these days. AI4WM has a good article on the web describing these poles . I found some with the fiberglass reinforcing ring on ebay fairly cheap. A trip to my local big box hardware store resulted in several "attachments pictured:

1. 1.5" Conduit Hanger - This allows me to attach coils, pulleys, etc to a mast or they can be used to attach to mast to something else (like a fence or a post).
   



2. 1.25" PVC Cross - This fits nicely over the top/male end of the mast.
   
   
   



3. 2" x 1.5" PVC Reducer - This I found in the electrical department. With a little drilling to add a few wire loops I should be able to use this to attach guys
   



4. 1.25" PVC Plug - This goes in the top (when mounted) arm of the PVC cross. It will give me a place to add a 6' whip above the top fiberglass mast.
   

read more "80 meter vertical"

More C-Pole Vertical Array

After building/using my two C-Pole array I'm starting to rethink my plan.

KF2YN's C-Pole vertical array design calls for dedicated C-Poles (each pruned to have a 25 ohm input impedance) and phasing lines that both transform the antenna impedance to 100 ohms and set the phase delay between the two antennas. On the surface this looks doable but I've a lot of concern about getting the phasing lines right. W8WWV's measurements showed about a 4% delta as he measured the electrical length of a 17.1' long piece of coax. Also, I don't want to dedicate two C-Poles to an antenna that I won't be using much.

A local friend of mine wants to build a self supporting C-Pole antenna like mine. I can feed two verticals with arbitrary (but equal) lengths of coax and a simple Tee connector at the antenna tuner to make up for the 25 ohm combined feed impedance...no need to worry about electrical lengths. In addition, self supporting antennas can be positioned anywhere to point my signal where I want it to go that day. I can even boost the gain a little (up to 4.8 dB) by separating the antennas 5/8 wavelength.

It's still August, I should have another couple of months of outside weather here in Minnesota.

read more "More C-Pole Vertical Array"

A Two C-Pole Steerable Array

Yesterday I finally got my two C-Pole phased array up and on the air. In fact, after tuning it a little I easily made two QRP contacts, one with N2UGB in NY and the other with CT4RL/1 in Portugal.

My journey from idea to an antenna was based on Chapter 13.3, "A Steerable C-Pole Array" in Brian Cake's book, "Antenna Designer's Notebook". Here Brian presented a design based on phased array theory and modeling. Brian was not aware of anyone that had actually built one.

The C-Poles themselves are made from Radio Shack 18 gauge stranded hookup wire. 1/2" PVC pipe is used for the top and bottom 40" spreaders. For easy supporting, the two C-Poles are in the same plane and aligned with the rope joining the two antennas. The upper inside corners of the antennas are connected by a 33.5' length of rope. This insures correct spacing. Support ropes are tied to the two top outside corners. Instead of a relay I used a coax T connector. L3 was added/removed as needed to change the radiation pattern.

Without L3 the array is endfire and, according to Brian's modeling, good for 1.18dBi gain. By adding L3 into the short/L2 side both sides become 3/4 wavelength long and the array has 3.5 dBi gain broadside.

I learned a little along the way about...

• Baluns and phasing lines...The phasing lengths include the phase delay introduced by the required choke baluns. I had planned to use air core baluns consisting of RG-8X wound around 4" plastic coffee "cans". What I found was that each balun takes about 1/4 wavelength (electrically) of coax. By the time I added the baluns to L1 and L2 in the accompanying diagram I couldn't separate the antenna by a physical half wave. I was forced to use more expensive ferrite toroid baluns that require less coax.
• Adding/removing L3...The switch/relay proposed by Brian in his design introduced its own challenges. The relay/switch is part of the phasing network. I found that my DPDT toggle switch with the needed connectors introduced more phase delay to the point that I was again in trouble with the physical separation of the two antennas. I eventually used a T connector instead.
• Supports...Finding trees with the right separation, orientation, height and limb placement can be a problem...especially for a temporary installation in the park.
• Measuring the electrical length of coax...My MFJ Antenna Analyzer gave a broad X=0 reading. My grip dip meter gave a sharp dip but not on the same frequency as the MFJ (The ARRL Antenna Book recommends against using a dip meter). Eventually I averaged the two MFJ endpoint/X=0 readings to get a center/single frequency and then calculated the coax electrical length based on that frequency.
• Gain...1 to 3.5 dBi of gain is hard to notice when asking for signal strength comparisons under real band conditions.
  

This antenna array may be a good alternative for someone with properly located supports but my typical picnic table operating style doesn't always allow that. This was as interesting exercise but I'll probably keep using my single C-Pole when I'm at the park.

read more "A Two C-Pole Steerable Array"

dBm Meters using the AD8307 logarithic amplifier

I'm having a go at building a couple of dBm RF Power Meter from AD8307

The first is W7ZOI design having found a nice 500uA meter at w/e there is a nice construction website here. Also note W&ZOI own notes on callibration here. There are plenty of variations on this design and the daa sheet and application notes from Analogue Devces are worth a read. Some like this one use an AF amp to provide an audible feedback too

Part of the circuit from the design from N2PON (QST August 2008) uses temperature compensation. Basically he divides the pin 4 output of the AD8307 that is fed to a DVM through a resistor network containing a 10K pot that adjusts the GAIN to achive c1mV/dB with an NTC temperature compensating thermistor (c1K at 25'C) connected to ground so if there is any temperature changes the instrument retains a level of thermal callibration.

In many places this is not necessary but I know from experience my own shack does vary from -10'C in deep winter to +30'C in summer if it is unheated. Any meter is likely to be built into a die-cast box that will take a while to equilibrate too... so I am trying to use a thermistor salvaged from a PC motherboard (as had a few) with a 2k7 value at 25'C and c4K close to freezing and 500ohms when about 100'C (basically put it in boiling water and into ice water and measured). So I think could use it but would adjust the value of by placing resistors in parallel and series with to obtain 1K at 25'C.

read more "dBm Meters using the AD8307 logarithic amplifier"

QRP operating at Myre-Big Lake State Park

This last weekend Beth and I took our camper trailer to Myre-Big Lake State Park near Albert Lea, MN. I had along my K1 and Crappie Pole 20 mtr C-Pole vertical.

As expected the C-Pole antenna worked well. Over the weekend I had 11 contacts including WA3SLN (PA), K4SPO (KY), K3WWP (PA), AF4O (TN), WB2PEF (NY), VA3RKM (ONT), WB6OJB (CA),WB4KLI (KY), WD9F (IL), W2IQK (NY) and W9LD (WA). I also started a QSO with AB7KT (NV) but that QSO was as victim of QSB/QRM/QRN.

Charles, K1ETU, from Oneonta, NY, spotted me and stopped by for an enjoyable "eyeball QSO". Bill, a camper from Louisville, KY, also stopped by bringing his two sons. Bill has been interested in ham radio since a teenager but had never gotten a license. Now he's thinking of locating a Louisville Radio Club and working on getting his ticket.

The crappie pole frame for my C-Pole really stands out in a campground. It looks like some sort of tall skinny game target or goal. Lots of campers noticed it as they walked or drove by, some asked about it. My favorite comment: "I've never seen a camping accessory like that before".

read more "QRP operating at Myre-Big Lake State Park"