More 1934 Transmitter

Remember the safety problem with my 1934 transmitter? One of the phone plugs is for metering and the other is for the key. If, in the heat of the moment, I get the two mixed up and plug the key into a B+ metering jack, I'll have over 300 volts on the key.

To protect myself I tied a length of string and a plastic cable clamp to the key phone plug (any lump of plastic would work). After the key is plugged in I slide the cable clamp under the front edge of the transmitter. The string is short enough that the plug can not be removed without getting the clamp out from under the transmitter.

read more "More 1934 Transmitter"

A 1934 transmitter - On the Air

Yesterday I set up my 1934 transmitter up with my NC101X and tried the pair out on 80 meters using my endfed 105' inverted "L" antenna only about 10'-20' off the ground. The station worked fine.

At 21:45 I had a nice QSO on 3570 with NG9D in Plainfield, IL. Lynn's signal varied from 589 to 599+. He reported that my 589 signal sounded fine/stable.

Also shown in the picture is my iambic keyer set up to key older tube rigs.

read more "A 1934 transmitter - On the Air"

More 1934 transmitter - It Works!

I've finished wiring my 1934 transmitter, powered it up and it works! With about 300 volts on the plates of the 46s and the 47 it loads to 15-20 watts input and 7-10 watts output. It sounds great also.

One change I made from the Bill Orr design is to connect the 47 screen to regulated 150V rather than a resistor network off of B+.

This transmitter is not without some personality, though. Only the amplifier stage is keyed so the oscillator stage runs continuously. On key up any energy from the oscillator that makes it to the antenna will be heard as a faint back wave. We'll see if this is objectionable. The second personality trait is, unfortunately, pretty nasty. When using the rig, one phone plug is for metering and a second is for the key. If in the heat of the moment I get the two mixed up and plug the key into a metering jack I'll have over 300 volts on my key. I'm planning something that will keep me from accidentally removing the key plug.

Eventually I plan is to mate this transmitter with my National FB7X for a complete 1934 station that I'll use in the 2010 AWA Linc Cundall OT CW Contest.

read more "More 1934 transmitter - It Works!"

More 1934 Transmitter

I've gotten the components all mounted and the transmitter is ready for wiring. I learned a few things along the way...

30s vintage Sangamo mica capacitors are large enough that they don't mount well on their own leads. Each one must be mechanically supported, either by a solder strip or by screwing to the wooden sides of the chassis.

The wooden chassis takes 1 1/2 inches of available length and width. This can impact the layout. Using an all metal chassis there is space for a buffer stage between the oscillator and amplifier. With 1 1/2 taken off the length/width plus the added reinforcing across the middle it would be a challenge to fit the buffer stage in there.

Will the lead length be a problem? Certainly I wouldn't trust this spread out layout at 30MHz but it may be OK on 7MHz. Time will tell.

read more "More 1934 Transmitter"

More 1934 Transmitter

After some quality table saw time, a bunch of drill press time and eight coats of paint (primer coat, satin black, three coats of wrinkle paint that didn't wrinkle and three more coats that did) I have a wood and aluminum chassis that looks pretty good. The layout is much like the Gross CW-25 but without the buffer stage. In place of the middle/buffer tuning dial I'm mounting a plate current meter. Across the bottom are three 1/4" phone jacks. One is the key jack. The other two are in the B+ circuits of the oscillator and final amp stages. These two jacks will have 350VDC exposed on the outside rim. For safety I recessed these jacks 1/2" behind the front panel. I also added a B+ switch on the far right.

I found two more examples of this tube lineup. One is a George Grammer construction project covered in November 1932 and February 1933 QST. The second is the Collins 4A transmitter.

read more "More 1934 Transmitter"

More 1934 Transmitter

After collecting all of the parts comes "playing checkers" to find the best layout given the set of parts located. In this case I found suitable 30's parts for all of the major components except the chassis itself. For it I'm using a 17"x10" sheet of 18 gauge aluminum. It will be fastened to a 4 1/2" tall wooden frame and then frame and aluminum painted black winkle.

read more "More 1934 Transmitter"

A 1934 Style Transmitter

Since the AWA Linc Cundall OT CW Contest in January I've been thinking about building another transmitter, this one falling in between my 1929 TNT transmitter and my Thordarson 100 or late 30's 6L6 transmitters. I want to use it with my National FB-7 so it needs to be an early to mid 30's design.

A popular design in the early 30's used a type 47 as a crystal oscillator driving a buffer and final on 160 through 10 meters. Typical power was anywhere from 20 watts on up depending on the tube lineup. The Gross CW-25 was one example. It had a 47 oscillator driving a 46 buffer/multiplier followed by two 46s in parallel. Plug-in coils were available for all bands 160 - 10. This looks like a pretty neat transmitter. More about the CW-25 can be found in Bill Orr's "Antennas" column in the February 1977 issue of CQ magazine.

I wish I could find a CW-25 available. Does anyone have one they will part with? In the mean time I'll have to homebrew something.

The cover story of the November 1971 issue on CQ magazine is a Bill Orr construction article describing a 160/80/40 meter "1934 Style Transmitter". Circuit-wise it is a close match to the CW-25 but without the buffer/multiplier stage. This circuit design fits my early/mid 30's requirement but the CW-25 chassis sort of construction better matches the "modern" look of my FB-7. I'll combine the two using the circuit from Bill Orr's article but building it to look more like the CW-25.

Notice that the schematic scanned from the original CQ article is missing the connection between the coupling capacitor C6 and the 46 tube grids.

read more "A 1934 Style Transmitter"