I had an idea to try and tidy things up in the shack and reduce the clutter. Why not use my under used Yaesu FT1000MP on data modes? I could then dispense with the little Kenwood TS450 I use for data, I could keep it as a backup rig or maybe sell it and buy some extra filters for the Yaesu.
So, I obtained a very reasonably priced data lead from http://www.radioarena.co.uk/. This arrived two days after placing my order-great stuff! I must say that although delivery was prompt there is no documentation with the interface whatsoever, nothing is labelled, even the two audio leads leave you to guess which is audio in and which is audio out!
Well this lead connects to the 5 pin DIN socket on the back of the Yaesu-labelled "packet"". I soon had the lead connected and was receiving PSK signals.Several hours later however I was still unable to get the rig to go into TX mode using Digipan or any other program. I could get data transmitted by manually keying the rig but no way of getting the PTT to operate via the interface. There could be a number of reasons for this- firstly the interface lead uses a USB rather than serial connector for which I had to install a Prolific driver. Secondly the Yaesu has to be set into "packet" mode for the PTT on the socket to activate, however despite doing all of this -no luck.
When DIGIPAN goes into TX the LED on the interface lights-so it is not a com port problem or a driver problem with the USB interface- the problem appears to be at the rig end. For now I have given up and re connected the little TS450 which works very well on data.This is not the first time I have tried and failed to press the Yaesu into use on Data.
The Yaesu FT1000MP is one of the few rigs I have owned from new. In fact it was the most expensive piece of equipment I ever purchased. For that reason alone I suppose I have tried to like this rig but in reality it is nowhere as good as perhaps I had thought it would be. for CW I prefer my old TS830s- it sounds so much nicer, for general receive I prefer my R5000 receiver, and the TS450 is easier for data. I guess the FT1000 does produce nice quality transmit audio though!
So, I obtained a very reasonably priced data lead from http://www.radioarena.co.uk/. This arrived two days after placing my order-great stuff! I must say that although delivery was prompt there is no documentation with the interface whatsoever, nothing is labelled, even the two audio leads leave you to guess which is audio in and which is audio out!
Well this lead connects to the 5 pin DIN socket on the back of the Yaesu-labelled "packet"". I soon had the lead connected and was receiving PSK signals.Several hours later however I was still unable to get the rig to go into TX mode using Digipan or any other program. I could get data transmitted by manually keying the rig but no way of getting the PTT to operate via the interface. There could be a number of reasons for this- firstly the interface lead uses a USB rather than serial connector for which I had to install a Prolific driver. Secondly the Yaesu has to be set into "packet" mode for the PTT on the socket to activate, however despite doing all of this -no luck.
When DIGIPAN goes into TX the LED on the interface lights-so it is not a com port problem or a driver problem with the USB interface- the problem appears to be at the rig end. For now I have given up and re connected the little TS450 which works very well on data.This is not the first time I have tried and failed to press the Yaesu into use on Data.
The Yaesu FT1000MP is one of the few rigs I have owned from new. In fact it was the most expensive piece of equipment I ever purchased. For that reason alone I suppose I have tried to like this rig but in reality it is nowhere as good as perhaps I had thought it would be. for CW I prefer my old TS830s- it sounds so much nicer, for general receive I prefer my R5000 receiver, and the TS450 is easier for data. I guess the FT1000 does produce nice quality transmit audio though!
Posts
No comments:
Post a Comment